Jumper SF810 8CH Full Range S-FHSS ontvanger SBUS PWM Output

16,99

De Jumper SF810 8CH Full Range S-FHSS ontvanger SBUS PWM Output biedt een hoogwaardige maar betaalbare S-FHSS-oplossing voor RC-piloten.
Compatibel met Jumper T16 en diverse andere zenders, zoals de Futaba SFHSS / FHSS-transmissiebronnen

3 op voorraad

Artikelnummer: HP056-0014 Categorie:

Beschrijving

De Jumper SF810 8CH Full Range S-FHSS ontvanger SBUS PWM Output biedt een hoogwaardige maar betaalbare S-FHSS-oplossing voor RC-piloten.
Compatibel met Jumper T16 en diverse andere ders, zoals de Futaba SFHSS / FHSS-transmissiebronnen, compatibel met de airzenders T4YF, T6J, T6K, T6K, T8J, T10J, T14SG, T18MZ, T18SZ of met de volgende zenders: 3PL, T3PRKA, 4PLS, T4PX, T4GRS .

De SF-serie kan worden gebruikt als een standaard PWM-ontvanger of in S.Bus-modus voor drones, ruimtevaartuigen, robotica, boot of iets dat een geavanceerd besturingssysteem gebruikt dat S.Bus-invoer vereist.
De SF-serie is een ontvanger met volledig bereik met dubbele antennes voor diversiteitsontvangst.

The Jumper SF810 has 8 PWM channels in Normal mode. In special mode, the 8th channel outputs Sbus while the remaining 7 channels output PWM.
In normal mode, the signal delay is 20.4mS, suitable for Analog servos. In the special mode, the delay is 13.6mS suitable for Digital servos.

Bind/Pair procedure:

Turn on your transmitter, select S-FHSS if it is necessary, press and hold the bind button on the receiver and power on the receiver, when the LED turns on solid green, the binding is finished, you can now connect servos to each channel and check for correct function from stick and switch movement on your radio.

Fail-safe settings:

The SF series receivers have a fail-safe mode similar to original Futaba Receivers. Before attempting flight, we strongly recommend that fail-safe modes are correctly set up on your receiver. For example, the throttle can be set to cut out in if the receiver enters a fail-safe mode to help avoid the model flying too far away.

PWM output mode and Sbus output mode Setting

PWM mode (normal mode) – All channels will output PWM. All SF series receivers are set to PWM as default. S.bus mode (Special mode) – The last channel of the receiver will output S.bus. All other channels will output PWM (excluding SF410 mini)

Changing Modes

Changing from Sbus to PWM is same as changing from PWM to Sbus:  turn off your transmitter, the LED is on red, hold and press the bind button for 6 to 0 seconds, release the button, then the red led will flash fast, press the bind button quickly once to confirm while the red led is still flashing.

Checking Modes

Connect any standard servo to the last channel of your receiver and give stick or switch the input on your radio. If the servo moves the receiver is in PWM mode (Normal Mode). If the servo does not move the receiver is in S.bus mode (Special Mode).

Note: If you want to reset the receiver back to normal mode, you can repair the receiver and transmitter.

LED status indicated under normal working status:

Features

  • Compatible with FUTABA SFHSS/FHSS 2.4GHz Transmitters
  • Air systems T4YF, T6J, T6K, T6K, T8J, T10J, T14SG, T18MZ, T18SZ
  • Ground system 3PL, T3PRKA, 4PLS, T4PX, T4GRS
  • Two modes, Normal (all PWM) and Special (PWM and S.Buss)
  • Dual diversity antennas

Specs

  • Working voltage: 3.6~8.5V
  • Working current: 45~60mA
  • Working temperature: 0-70 °C
  • Delay: Normal Mode 13.6mS / Special Mode 20.4mS
  • Effective distance: >1.8km 
  • Weight: 7.8g
  • SBUS: Yes

Includes

  • 1x Jumper SF810 Receiver

Beoordelingen

Er zijn nog geen beoordelingen.

Wees de eerste om “Jumper SF810 8CH Full Range S-FHSS ontvanger SBUS PWM Output” te beoordelen

Het e-mailadres wordt niet gepubliceerd. Vereiste velden zijn gemarkeerd met *